Trusted in Homes and Hospitals
Health workers appreciate the extra safety provided by our shower water retainer. Safety is increased by retaining water in the shower areas to keep the rest of the area dry preventing slips. Roll in, barrier free, curbless shower stalls all can benefit from using our collapsible shower water retainer dam.
Easy to Install
To install the retainer dam simply trim the strip to fit, remove the backing from the self adhesive strips, and apply in place directly below the shower curtain rod. It can be cut to your measurements or shipped in a bulk roll for multiple jobs.
Industrial Strength Materials
The water retainer dam is made of a high density memory foam that returns to it’s original shape after it has been rolled or stepped on. It’s unique fence-like shape catches the bottom of the shower curtain to prevent it from blowing out over the water dam.
To ensure the water dam is able to catch your shower curtain you can use our extra long shower rings to easily lower your shower curtain to the proper height. Also, ourshower curtain kits seal the curtain edges to either side of your accessible shower providing even greater curtain control.
Government and Construction Industry
- NASA – Texas
- United States Army – AE
- TBA Construction – SC
- Kellogg and Kimsey – TX
- AM Carpet Service – NY
- G&K Dev Co – NW
- Medeba Summer Camp – Ont
- Health Track and Wellness – PA
- YMCA – MN
- Hillside Lake Park Recreation – Ont
- Smithsonian Museum – New York
- Sheridan College – WY
- Emory University – GA
- University of Plattsburgh – NY
- Minnesota State University – MN
- Johnson & Wales University – NC
- MSUM University – MN
- Minnesota State University – MN
- University of Tennessee – TN
- Texas State University – TX
- Stanford University – CA
- Miami University – OH
- Lake Michigan College – MI
- Whispering Palms Inn – TX
- Quality Inns – CA
- Hyatt Regency – FL
- Hampton Inn Suites
- Holiday Inn – CA
- Days Inn – AL
- The Beachmere Inn – ME
- Clearwater Casino – WA
Hospitals, Assisted Living and Medial Suppliers
- Mount Sinai Hospital, Toronto
- University Medical Center, Texas
- Community Hospital – CA
- Wallowa Memorial Hospital – OR
- Annapolis Royal Nursing Home – NS
- Las Ventanas Lifecare Community – NV
- Dubois Housing Authority – PA
- Community Living Windsor – Ont
- St. Joseph Apts – MO
- Benton Village Project – GA
- MediChair – Ont
Frequently Asked Questions
What do you do for end cap or when the dam comes in contact with the shower wall?
If your wall come down on a right angle to the shower base, then you can put some silicon where the dam meets the wall.
If you have more a cove or round area where the wall meets the shower base, we suggest using our end caps or plugs product.
What should I do if the water dam starts to lift or is caught and the adhesive lets go?
Some tile sealer products can effect a good bond or a section can be caught and breaks its seal – exterior construction adhesive such as Liquid Nail or PL 2000 which is found in most hardware stores.
How long should I expect the rubber dam to last.
Our rubber dams were build to last and the adhesive is bonded to the base of the dam. We would expect 12 -15 years however you may have to apply additional adhesive at sometime during the lifetime of the rubber.
Which way should the lip on the Water Dam face?
The flat lip should be facing the drain inside the shower unit.
How to make a curve or right angle with a shower water dam?
You can make a series of relief cuts to allow for an overall slight curve when attaching the water dam to the shower unit. In some cases, a home owner may need to make a right turn with the water dam. This is done by cutting out a small triangle shape on the one side of the water dam base that does not have the vertical loop. By cutting out the triangle in the base, this allows for a right angle turn without cutting through the vertical loop.
For more detailed instructions and a photo please see this blog post.